全自动聚乙烯压痕硬度测定仪

SLYQ-96A/3路

一、满足尺度：

GB/T 23257-2009 埋地钢质管路聚乙烯防腐层

二、全自动聚乙烯压痕硬度测定仪概述：

本仪器重要测试聚乙烯在肯定的温度环境和恒定的压力下经过肯定的功夫后的压痕深度。

本仪器是国内自动化水平zui高，zui的测试聚乙烯压痕硬度的测试仪器，由于做的功夫比力长，试验人员只必要在试验前设定好参数后，会自动凭据设置的尝试前提进行加温，并维持恒温，可能自动加载，并自动采集了局、推算均匀数值。尝试实现后有报警提醒，报警功夫长短能够设定！

    三、全自动聚乙烯压痕硬度测定仪产品特点：

1、本仪器主题节造部门通过7寸触摸屏设置参数并节造。

2、本仪器变形采集利用国内的微型位移传感器技术，裁减了利用数字千分表采集位移精度低、易坏及必要更换电池等缺点

3、设置好参数后，点起头尝试后自动加载，尝试实现后自动推算了局，同时压头自动复位到初始地位进行下次尝试

1. 同时能够做三路尝试，也能够单独进行一路或二路
2. 本仪器带有微型打印机，能够对试验了局进行打印，并自动推算均匀值。
3. 测试环境温度为：室温-100度，温度可设定
4. 拥有报警提醒，尝试实现后凭据设定的报警功夫进行报警。

四、全自动聚乙烯压痕硬度测定仪技术参数：

1、试验负荷：10MP（25N）

2、压头直径：Ф1.8mm

3、控温精度：±0.5度

4、压痕深度批示zui幼分度值：0.01mm

5、耐压功夫：能够设定

6、主机变形量：≤0.04mm

7、丈量领域有效值：能够设定

8、允许zui大试样厚度：50MM

五、全自动聚乙烯压痕硬度测定仪重要配置及附件：

　    1、主    机：        一台

　    2、主机压头￠1.8mm：三个

      3、微型打印机：      一台

      4、自动加载装置：    三套

      5、位移传感器：      三个

      6、恒温加热装置：    一套

      7、使用说明书：      一份

      8、德国西门子PLC：  一个

      9、德国西门子采集？椋阂桓

      10、寸彩色触摸屏：  一个

英文资料简介如下：

 Full automatic polyethylene indentation hardness tester

SLYQ-96A/3 Road

One, meet the standards:

GB/T 23257-2009 polyethylene coating for buried steel pipeline

=====================================

Two, automatic determination instrument of polyethylene indentation hardness:

The instrument is mainly test of polyethylene in a definite temperature environment and the constant pressure after indentation depth after a certain time.

This instrument is the highest degree of automation, test instrument most leading testing polyethylene indentation hardness, as a result of the relatively long time, test personnel only need to set parameters in the test before and after, will automatically according to the experimental conditions set for heating, and keep constant temperature, capable of automatic loading, automatic acquisition and calculation results, the average numerical. After completion of the experiment has alarm, alarm time can be set!

===============================

Three, automatic indentation hardness tester product features of polyethylene:

1, the instrument is the core control part through a 7 Inch Touch screen set up parameters and control.

2, the collection and utilization of micro displacement sensor deformation technology leading, eliminated using digital micrometer acquisition displacement precision is low, easily broken and the need to replace the battery and other defects

3, after parameter setting, some began to automatic loading experiment, automatic calculation results after the experiment, at the same time indenter automatic reset to the initial position for the next experiment

4, at the same time can do three experiments, can also be a road or two separate

5, the instrument with a micro printer, you can print the test results, and automatic calculation of average value.

6, test environment temperature: room temperature -100 degrees, the temperature can be set

7, an alarming, after completion of the experiment according to the set alarm time and alarm.

==========================================

Tester technical parameters four, full automatic polyethylene indentation hardness:

1, the test load (25N): 10MP

2, the pressure head diameter: 1.8mm

3, temperature control precision is ± 0.5 degrees:

4, the indentation depth indicates the minimum scale value: 0.01mm

5, pressure time: you can set

6, the host deformation: ≤ 0.04mm

7, the effective value measurement range: can be set

8, to allow maximum thickness: 50MM

==============================

Five, automatic indentation hardness tester of polyethylene main configuration and accessories:

1, the main machine: a

2, the host head - 1.8mm: three

3, micro printer: a

4, automatic loading device: three sets

5, the displacement sensor: Three

6, a constant temperature heating device: a

7, the use of manual: a

8, Germany Siemens PLC: a

9, Germany Siemens acquisition module: a

10, inch color touch screen: a